The Podcatcher can sound an warning beep when it receives a signal from the Warning IDentifier, which might help preventing Podcatchers from going missing. In the specsheet you’ll find more information about the Warning IDentifier.
Category: Manuals & Specsheets
Specsheet Audio
You can find more information about the audio files here Specsheet Audio.
Specsheet Syncconsole (NUC)
The Syncconsole is the connection between the Podcatcher Portal and the hardware. Standard Syncconsoles delivered by us, will have TeamViewer installed so we are able to connect with the Syncconsole from a distance. If you would like our support, you can always contact our helpdesk. If we have to look into the Syncconsole to resolve a problem, we will inform you first.
We always recommend to connect the Sycconsole onto your ‘guest network’ so your internal network is protected at all times. Your system administrator will be able to do this for you as it’s his responsibility.
This specsheet gives you more information about the Syncconsole we deliver, a NUC.
Specsheet E-mail console
At the end of a tour, visitors can view which content they have listened to and what they have missed by using MapMyVisit. Visitors just leave their email in the E-mail Console so they can access the tour online, after the automatic sync.
More information about the use and installation of the E-mail Console can be found here Specsheet E-Mail Console (Map My Visit)
Specsheet Cabinet Block & Tower
The Cabinet Block is a stand alone compact charging and synchronization unit, that can hold up to 100 Podcatchers (10 dockingstations).
The Cabinet Tower is a unit that can hold up to 300 Podcatchers. The Tower configuration exists of 4 cabinet blocks; 3 with Podcatchers and one empty block to ensure the right height.
Please take a look at this the specsheet for more information and measurements;
Specsheet Cabinet Block and Tower 2020
If you wish to make your own furniture, please have a look on this page
Specsheet AV-Sync (IDentifier)
The Podcatcher can synchronously play the audio of a movie when the movie is equipped with a AV-Sync Track.
In the specsheet you can read what a AV-sync set contains and what the measurements are: Specsheet AV-Sync
Specsheet Dockingstation
The Dockingstation is a compact charging- and synchronisation station that can hold up to 10 Podcatchers. Please take a look here: Specsheet_Dockingstation for info and measurements.
Note: a Dockingstation can be placed on a flat surface (table-top) or wall-mounted. It is also possible to built the Docks in a piece of furniture. There are a few guidelines to keep in mind when doing that.
Specsheets IDentifiers
Underneath you find the specsheets of our newest model IDentifier (V3) and our older model IDentifier (V2).
Specsheet IDentifierV3
Specsheet IDentifierV2
Note; the IDentifier V2 will no longer be available in our product range as of the 1st of January 2021. Customers can keep using them on location, but we cannot replace them or send out additional ones.
Specsheet Podcatcher
The Podcatcher is an interactive audio handset. It can be used for all types of interpretation and interaction, anything from a simple audio guide, to a remote control for an interactive exhibition or game. The specsheet can be found here: Specsheet-Podcatcher-2020
Replacing the battery of IDentifiers
After a while – a year or two in indoor environments – an IDentifier’s battery will eventually run dry. When this happens, replacing it is fairly simple. This page aims to teach you how to do so.
Object IDentifier
The process of replacing batteries is as follows, depending on the type of IDentifier you have;
- Remove frontside using a fine flat screwdriver.
- Carefully take out the PCB with transmitter and batteries.
- Replace the 2 CR2032 lithium coin cells (batteries) off the transmitter.
- Re-assemble the IDentifier.
Instruction-sheet Instruction IDentifierV2 Battery
- Remove frontlabel using a fine small knife.
- Remove the 4 screws with a T6-screwdriver
- Remove the top cover whilst keeping the sealing in the front side.
- Carefully take out the PCB with transmitter and batteries.
- Replace the 2 CR2032 lithium coin cells (batteries) off the transmitter.
- Re-assemble the IDentifier.
Instruction-sheet Instruction IDentifierV3 Battery_
Done!
English 
Nederlands 
Français